![]() If configuring this as 2 separate basic SIP phones, then Line 2 should use a different End User in CUCM, and will need the Auth ID in the WRP to be filled in with it. This last screenshot shows Line 1, Line 2 should be configured the same way except for the User ID which would be the other Directory Number. Password is the End User password in CUCM The other way to add it is, to insert two different Basic Third Party SIP Phones, each one of them registering a different line from the WRP.Ĭlick on Line 1 and Line 2 to configure different extension numbers matching what you have in CUCM: Although on the GUI we saw it as "Partial Registered", we could call in and out from the analog phones attached. This is how we got a WRP400 to register both lines with CallManager as an Adanced Third Party SIP phone. Now create a new account and configure it: Note that 1001 is the directory number configured in the 3rd party phone config page, and 192.168.1.10 is Callmanager's IP.CM detects them duplicate and rejects authentication) Ekiga detects 2 NICs, and sources REGISTER messages with each IP configured. Buenos días, lo que deben hacer par solucionar este inconveniente es ir al menú configuraciones y luego configuración sip asterisk, en la pestaña de pjsip, poner el puerto 5160 y en chan sip poner el puerto 5160, esto resuelve el problema de que las extensiones chansip no podía autenticarse. Now lets open Ekiga and configure it: go to Edit > Preferences > General > General Settings > Disable network detection (this might cause loops issues where Callmanager refuses the REGISTER message. My SIP client, Zoiper, cannot register with any service while Voice Over. That should be it from the Callmanager side. I am attempting to use Zoiper on my 3T while on my LAN connecting to my VOIP.One of the associated phones is MAC 044B80808003, that one is the SIP phone I already added Check how the "Controlled Devices" box looks like.Create an End User in Callmanager the username and password will be used in the Ekiga account for authentication.I have set up Zoiper on my laptop (connected by wifi to router ), and it will not connect to the sip provider. Ie it works on 3g/4g, but will not register to my Sip provider via wifi. *** DO NOT FORGET THIS STEP *** The phone wont register if the correct digest user is not used My Zoiper phone connection works if my phone is off of my wifi. If there is still no user ready at this point, carry on and come back to this point when ready. In my case I already have a user associated that will be shown in the next steps. Go to the section called Protocol Specific Configuration: and select the Digest User that is going to be associated to this phone.3rd party SIP phones do not use this value to achieve registration The MAC may be a dummy value, but I choose the PC where Edika is installed. Go to Device > Phone > Add new > Type: Third party SIP Phone Basic and fill in the required values.Will try to add other SIP devices at the end of the doc. Once configured you will be taken to the Zoiper Home screen.I will show how to register Ekiga softphone to Callmanager 7.1.2, I haven't tried it on anything earlier but it should be pretty simillar. Once one is found and all have finished searching you may click Next Zoiper will now test your network and automatically configure the software based on your network. From Services > Softphones > Then click on your extension to see the outbound proxy. Please use the proxy listed in your portal. You will then be presented with Authentication and Outbound proxy. You will be prompted to fill in your hostname, This should auto populate based on what you have entered in the previous screen so you may click Next. In the next screen type the information of the phone extension as explained in this image: Once you’re done click on Register. Now click on Accounts, click the plus sign and then Yes, and next click Manual configuration. (You will receive a welcome screen which gives you the option to activate a premium license, Learn more or you may Continue as a free user.) If using Zoiper with WiFi, please make sure that the routing device is not blocking ports used by Zoiper. Now go back to the Zoiper APP and click on Settings. Once the application is installed, launch the application. When asked for a Transport Method, choose either TLS or TCP. ![]() Under Services > Softphone - select your extension to view your login information. You can skip the Optional: Authentication and Outbound Proxy step, this is not needed. While the application is downloading, please visit your portal at to gather your login information. How to Register a Zoiper Soft Phone Open Zoiper and navigate to the Settings dropdown and select Preferences Then in the General tab input the following. You may gather the information to help you with setup from Services > Softphones > then use the dropdown to select your account. This article will guide you through registering your extension on Zoiper 5 desktop
0 Comments
Leave a Reply. |